![]() USB 2.2 × CAN (2.0B Active) and SDIO interface.Today, Painless is headquartered in a modern 45,000 square foot facility in Fort Worth. As the company grew and more products were developed, the name was changed to Painless Performance in 1998 to better reflect the growing divergence of the product line. ![]() Up to 6 SPIs (45 Mbits/s), 2 with muxed full-duplex I 2S for audio class accuracy via internal audio PLL or external clock The name caught on and soon Perfect Performance became Painless Wiring.Up to 4 USARTs/4 UARTs (11.25 Mbit/s, ISO7816 interface, LIN, IrDA, modem control).Up to 3 × I 2C interfaces (SMBus/PMBus) I see painless performance is now doing a diesel module, anyone try one out yet 2006 2500hd, LBZ/allison,CC,SB 2wd SLT 20x9.Up to 168 I/O ports with interrupt capability.Up to 17 timers: up to twelve 16-bit and two 32-bit timers up to 180 MHz, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input.General-purpose DMA: 16-stream DMA controller with FIFOs and burst support.3×12-bit, 2.4 MSPS ADC: up to 24 channels and 7.2 MSPS in triple interleaved mode I am using a Painless Cirkit Boss 70117 to power my MSD 6A box and Atomic EFI.V BAT supply for RTC, 20×32 bit backup registers + optional 4 KB backup SRAM.32 kHz oscillator for RTC with calibration Product Line: Painless Performance 21-Circuit Universal Harnesses.Internal 16 MHz factory-trimmed RC (1% accuracy).1.7 V to 3.6 V application supply and I/Os.Chrom-ART Accelerator™ for enhanced graphic content creation (DMA2D).LCD-TFT controller with fully programmable resolution (total width up to 4096 pixels, total height up to 2048 lines and pixel clock up to 83 MHz).LCD parallel interface, 8080/6800 modes.Flexible external memory controller with up to 32-bit data bus: SRAM, PSRAM, SDRAM/LPSDR SDRAM, Compact Flash/NOR/NAND memories.Up to 256+4 KB of SRAM including 64-KB of CCM (core coupled memory) data RAM.Up to 2 MB of Flash memory organized into two banks allowing read-while-write.Core: Arm® 32-bit Cortex®-M4 CPU with FPU, Adaptive real-time accelerator (ART Accelerator™) allowing 0-wait state execution from Flash memory, frequency up to 180 MHz, MPU, 225 DMIPS/1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions Complete painless wiring kit for a cj 7 500 cost alot more but it used.You can see in the top left corner I still have some pre-run wires that I could connect to power for future use. I have installed a Ballistic 8 cell EVO2 battery that only takes up 1/3rd the space of a traditional lead acid or AGM battery. You can see I chose to mount the relay for the stebel separately. Torque Converter Lockup Kit, Vacuum Switch, GM 700R4, Kit. I have added heated grips, stebel horn, Powerlet 12v BMW style outlet for heated clothing, phone and gps power. Painless Performance 60109 - Painless Performance 700R4 Converter Lock-Up Kits. The Versys doesn't have a lot of extra room for this stuff. So i just got my painless performance digital power manager. A product like the Centech AP1 or AP2 is very simple to wire only the circuits you need. The attached relay and the permanently wired wires on the Painless made it more difficult to find a suitable, neat location for the installation. It had the wires and relay pre-wired and ready to connect to the bike. I have used a Painless similar to the one you linked and it was a high quality product.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |